|
Safe &
Secure Online Ordering |
|
............................................... |
|
FREE
SHIPPING IN CONTIGUOUS U.S.! |
|
|
|
WATER
SOFTENERS |
|
|
|
|
Osmonics/Autotrol 255 Valve with the 760 Logix
Control for 3/4" Plumbing
 The 255/760 computer/demand
control system for 3/4" plumbing combines design simplicity with
reinforced NORYL construction to provide you with an uncommonly
reliable appliance. The inherent reliability for the system means a
long life of efficient, trouble-free, uninterrupted soft water
luxury
Should maintenance become
necessary, the Series 255 offers a unique "separation" capability.
Other components, such as the computer control, are modular, making
it by far the most home-owner friendly valve on the market.
Here's a few of the key
features of the 255 valve:
- Fewer parts than other softener valves.
- Single motor provides all the power to turn camshaft - no
solenoids are needed!
- Unique camshaft / flapper valve design - no dynamic seals
(such as piston and seal or rotary discs) that could cause
leakage through wear or fatigue.
- Built-in brine control valve - no external brine float
needed!
- Direct acting system functions independent of water
pressure. No pistons or diaphragms that require a minimum water
pressure to operate.
- Valve may be indexed manually without power in the event of
an extended power outage.
- True 3/4" internal porting - many competitors use
restrictive 1/2" internal ports!
- Energy-efficient - uses only about $2.00 of electricity per
year!
The two key features of the
760 Logix demand system are the microprocessor, and a water meter
located on the valve outlet. The flow of soft water through the
turbine meter generates electrical impulses that tell the computer
the amount of water being used. Every day, at 2:00 am, the past 7
days' water usage is statistically analyzed to anticipate the amount
of water that will be used the next day. The computer then
determines if the softener has enough remaining capacity to supply
the next day's needs - if not, the unit will regenerate. If the
water usage pattern changes, the computer automatically compensates
for the change and regenerates only when needed. This results in
higher operating efficiency and lower salt usage compared to other
systems.
Here's a few of the key
features of the 760 Logix computer control softener valve:
- Only one moving part - the turbine in the water meter. No
reduction gears like other units!
- NOVRAM chip retains programming information in the event of
a power outage.
- Self-adjusting reserve - keeps it to a minimum for optimum
efficiency.
- Flow indicator flashes whenever water is flowing through the
valve.
- Calendar override feature can be programmed to initiate a
regeneration at a fixed interval if water usage has not been
enough to trigger it - beneficial on iron-bearing water.
 In
addition to the original 760 control, we now offer the 762 upgrade
control. This advanced controller allows you to adjust the
individual regeneration cycles to "fine tune" to your conditions.
For example, if you have a sediment filter on before your softener,
you don't need the backwash cycle to go the full 14 minutes - you
can shorten it to conserve water. Or if you have high iron, you may
wish to lengthen the cycle to be sure to remove it from the resin.
This upgrade is only $75 more!
Read more about the Logix controller
HERE.
Downloads:
Logix Series Controllers Brochure
(261 KB)
Logix Series Manual
(5.7 MB)
Logix Quick Start Guide
(150 KB)
Water Softener
Assembly Instructions
(52 KB)
Water
Softener Sizing Calculator
Email us!
|
255/760-0.75: 3/4 cubic foot of resin (23,000 grain peak capacity) -
$1,125 list, your cost - $799 with free shipping
in the contiguous U.S.!
|
|
255/760-1.0: 1 cubic foot of resin (30,000
grain peak capacity) - $1,200 list, your cost - $849
with free shipping in the contiguous U.S.!
|
|
255/760-1.5: 1 1/2 cubic foot of resin (45,000 grain peak capacity)
- $1,306 list, your cost - $929 with free shipping
in the contiguous U.S.!
|
|
255/760-2.0: 2 cubic feet of resin (60,000 grain peak capacity) -
$1,532 list, your cost - $999 with free shipping in
the contiguous U.S.!
|
|
Optional
762 Upgrade (allows modification of all cycles), YOUR PRICE -
$115.00, with water softener purchase.
|
|
Optional
Autotrol Turbulator
for better iron removal - only $25 with water softener purchase!
(Note: cannot be used with the MediaGuard)
|
|
Optional Brine Tank Over-Flow
Shut-Off: The standard brine tank set-up has a simple overflow
fitting where tubing is connected to direct overflow to a floor
drain should a malfunction occur. You can add a brine tank safety
float shut-off if a floor drain is not nearby.
Only $50.00 with water softener
purchase.
|
DIMENSIONS:
255/760-0.75: Main unit - 8"
diameter X 52.5 tall, brine tank - 15 X 17 X 36 (275 lbs. salt
capacity)
255/760-1.0: Main unit - 9" diameter X 56.5 tall, brine tank - 15 X
17 X 36 (275 lbs. salt capacity)
255/760-1.5: Main unit - 10" diameter X 62.5 tall, brine tank - 15 X
17 X 36 (275 lbs. salt capacity)
255/760-2.0: Main unit - 12" diameter X 56.5 tall, brine tank - 15 X
17 X 36 (275 lbs. salt capacity)
Note: 11 X 11 X 38 brine tank
(smaller footprint, 170 lbs. salt capacity) is available at no extra
charge - simply indicate it in the "Comment" box.
SOFTENER SPECIFICATIONS:
Water Softener Specifications
|
